Autometer Arctic White 3-3/8 Quad Gauge and Tach/Speedo Combo

Product 1309 DESCRIPTION:
Sometimes space is limited. The AutoMeter Quad Gauge provides a solution to limited dashboard space while providing a clean look. Individual AutoMeter air core meter movements for each function provide the accuracy and durability required by even the most demanding applications. Includes a single wire 1/8” NPT temperature sender and a 1/8” NPT oil pressure sender. The voltmeter reads from 8-18v on negative ground electrical systems and fuel level resistance range is 240 ohms empty to 33 ohms full (compatible with AutoMeter’s 3262 fuel level sender).
Feature Points
Traditional incandescent lighting illuminates around the perimeter of the dial
Kit includes fuel level sender (240E/33F), oil pressure sender, water temperature sender, 2-wire hall-effect speed sender that is compatible with GM/Chrysler applications (7/8" - 18THD), sending unit adapters (1/4", 3/8”, and 1/2" NPT adapters), bulb and socket assemblies, red and green bulb covers, mounting hardware, and detailed instructions for installation.
AutoMeter’s race proven air-core electric instruments provide quick and accurate readings while keeping hazardous fluids outside of the vehicle
12 and 16 volt compatible, compatible with nearly every street car or race car electrical system
Speedometer has a simple push button, 2 mile drive calibration. No dip switches and can be reprogramed at any time to accommodate changes in gear ratio or wheel and tire combination.
Tachometer is compatible with 0.5 - 6 pulse ignition signals (1-12 cylinder engines) with points, electronic, and most 12V high-performance racing ignitions.
Speedometer is compatible with most two wire sine wave and three wire hall effect vehicle speed sensors.
Speedometer features lit LCD odometer - capable of registering one-million miles with two resettable trip odometers
4 in 1 gauge design saves valuable real estate on your dash while allowing you to monitor critical parameters
Domed Lens
Ships With
Includes Sending Unit: Fuel Sender 3262 - Oil Sender 2242 - Water Sender 2258 - 5293 VSS Sensor
1/8" NPT Male to 1/8" compression fitting, 1/8" NPT Female to 1/8" compression fitting, 1/8" NPT to 1/4" NPT bushing, 3/8" NPT and 1/2" NPT adapter fittings.
Brackets Included
California Residents: Prop 65 WARNING
REVIEWS:
Search topics and reviews
Search topics and reviews
ϙ
Search
★★★★★
No rating value
Be the first to review this product
. This action will open a modal dialog.
Write a review
QUESTIONS:
★★★★★
★★★★★
No rating value for 2 PC. GAUGE KIT, 3-3/8" QUAD & TACH/SPEEDO, ELECTRIC, 240-33 Ω, ARCTIC WHITE
Search questions and answers
Search questions and answers
ϙ
Search
0
Reviews
10
Questions
10
Answers
Questions
Ask a question
1–10 of 10 Questions
Sort by:
▼
Menu
Joshieboy
· 7 months ago
Will this speedometer work with the 5289 GPS adapter?
1
answer
Answer this Question
Steve from AutoMeter · 7 months ago
Yes, all of our electronic speedometers will work with P/N: 5289. For further assistance, please contact us at 866-248-6357.
Helpful?
Yes · 0
No · 0
Report
Dukesy
· 3 years ago
Do these gauges come in Km/h and metric temp ?
1
answer
Answer this Question
Steve from AutoMeter · 3 years ago
Unfortunately that specific gauge set does not come in Km/h or metric.
Helpful?
Yes · 0
No · 0
Report
P1800
· 3 years ago
I am looking to buy the #1309 2 piece kit and will need a #5920 universal magnetic sender. Can I order # 1309 substituting this sender? 2nd ? is this unit available in a 4 1/2" or 5" size? 3rd? can you send me a PDF actual size image of the gauges?
1
answer
Answer this Question
Sarah from AutoMeter · 3 years ago
Thank you for contacting us. There are substitutions we can do on kits. You would have to purchase the 5290 separately. You can price our each gauge individually + the 5290 to see which would be more cost effective. The 1303 is a 4-5/8” kit but it would not include the tach/speedometer combo. We do not offer a 4-5/8” combo in the Arctic White Series.
Helpful?
Yes · 0
No · 0
Report
NateNate
· 5 years ago
Is it possible to pre-set the odometer so that it matches the vehicles existing mileage?
1
answer
Answer this Question
Steve from AutoMeter · 5 years ago
You can send the gauge into us to have this done. You will need to simply send a note in with the unit and state the mileage you would like us to set the gauge.
Helpful?
Yes · 0
No · 0
Report
carguy44
· 5 years ago
Do you have #1309 with a diesel tach? Do you have an 3-in-1 Boost, Trans temp, EGT 3 3/8"?
1
answer
Answer this Question
Steve from AutoMeter · 5 years ago
You can use P/N: 9112 to convert any tachometer into a diesel tach. We do not sell any 3-in-1 gauge sets.
Helpful?
Yes · 0
No · 0
Report
69Stang71Cuda68charger
· 5 years ago
HI i was just wondering if this gauge kit would fit in a 74 cuda with a rallye dash gauge?
1
answer
Answer this Question
Steve from AutoMeter · 5 years ago
Thank you for your question. Unfortunately we have not installed these in that specific dash. I would recommend measuring the hole sizes and getting in contact with our tech line for further assistance 866-248-6357.
Helpful?
Yes · 0
No · 0
Report
Rbtschug
· 5 years ago
Will your gauges work with stock sending units?
1
answer
Answer this Question
Zach from AutoMeter · 5 years ago
Thank you for question. Unfortunately, our gauges will not work with OEM sending units. You will need to use the included sending units for them.
Helpful?
Yes · 0
No · 0
Report
Frank S
· 5 years ago
Are the gauges a direct fit.
1
answer
Answer this Question
Zach from AutoMeter · 5 years ago
Thank you for your question. None of our gauges are made to be direct fit factory replacements. These gauges will fit in a 4-5/8" hole.
Helpful?
Yes · 0
No · 0
Report
Earl J
· 5 years ago
Does this come with the mounting brackets? Also, do the gauges light up?
1
answer
Answer this Question
Zach from AutoMeter · 5 years ago
Thank you for your question. Yes, these gauges will include mounting brackets as well as incandescent bulbs that provide perimeter back lighting.
Helpful?
Yes · 0
No · 0
Report
Gus F
· 5 years ago
How do you calibrate the tachometer in this gauge set to correctly read the rpm of a 6 cylinder engine?
1
answer
Answer this Question
Zach from AutoMeter · 5 years ago
Thank you for your question. Here is a link to our installation instructions for this gauge. Calibrating instructions can be found under the PPR section: https://www.autometer.com/media/manual/2650-1175.pdf
Helpful?
Yes · 0
No · 0
Report
Ask a question
You may also like:
RPM SIGNAL ADAPTER FOR DISTRIBUTORLESS IGNITIONS
Product #9117
$113.58
SPEED SENSOR, MECH TO ELEC, GM & CHRYSLER, 7/8"-18 THREAD, HALL EFFECT, 16 PULSE
Product #5291
$113.94
SENSOR, SPEED, MECH TO ELEC, FORD PLUG-IN, HALL EFFECT, 16 PULSE
Product #5292
$113.36
SENSOR MODULE, GPS SPEEDOMETER INTERFACE, 16 FT. CABLE, INCL. GPS ANTENNA
Product #5289
$250.73
SPEED SENSOR, UNIV. MAGNETIC, HALL EFFECT, INCL. QTY. 4 MAGNETS & BRACKET ASSY.
Product #5290
$103.15
WIRE HARNESS, PLUG & PLAY GM LS ENGINES, FOR #9117 TACHOMETER ADAPTER
Product #2189
$109.29
Also Purchased With
2 PC. GAUGE KIT, 3-3/8" QUAD & TACH/SPEEDO, ELECTRIC, 240-33 Ω, DESIGNER BLACK
Product #1409
$626.66
2 PC. GAUGE KIT, 3-3/8" QUAD & TACH/SPEEDO, ELECTRIC, 240-33 Ω, OLD TYME WHITE
Product #1620
$599.99