Autometer Fuel Signal Adapter for AM Gauges

Product 9109 DESCRIPTION:
The Fuel Bridge wires in between your fuel level gauge and sending unit and allows you to use any AutoMeter 90 degree short sweep electric fuel level gauge with any stock or aftermarket sending unit. The triple push button with LED display allows for easy set up. This unit is a compact size at 3 1/8" wide x 2 1/2" tall x 3/4" thick. A low fuel level warning is available at 10% and off at 15%. It can turn on an LED or relay.
Feature Points
Allows you to use any AutoMeter 90 degree short sweep electric fuel level gauge with any stock or aftermarket fuel sending unit
Three push buttons with LED display for easy set up
Low fuel level warning at 10% and off at 15% with ability to trigger LED or relay
8 pre-programmed resistance ranges for popular fuel level sending units
Configurable option with linear adjustments at 5 points (F, ¾, ½, ¼, & E) anywhere between 0-1000 or 1000-0 ohms
Compact size - 3“ x 2-½" x ¾"
Pre-programmed for the following: 240/33, 0/90, 0/30, 16/158, 73/10 (linear and non-linear), 10/180, 40/250
California Residents: Prop 65 WARNING
Videos:
REVIEWS:
Search topics and reviews
Search topics and reviews
ϙ
Search
Write a review
. This action will open a modal dialog.
California
Review 1
Votes 2
★★★★★
★★★★★
5 out of 5 stars.
Received my Fuel Bridge yesterday.
Purchased a 5" cluster gauge along with the Fuel Bridge for my 34 Chrysler Street Rod.
Awesome product and pretty easy to install. Pretty cool how it's programable for different sending units. One thing was a little hard. You must back out the wire screws all the way then press the wire clip with a pointed object like a wire probe' other wise you cannot get the wires under them. Not a big deal just had to figure it out . Great product and Gauge.
Recommends this product ✔ Yes
Helpful?
Yes · 2
No · 0
Report
Write a review
QUESTIONS:
★★★★★
★★★★★
5 out of 5 stars. Read reviews for FUEL BRIDGE, FUEL SIGNAL ADAPTER FOR AUTOMETER GAUGES
5.0
1 Review
This action will navigate to reviews.
Search questions and answers
Search questions and answers
ϙ
Search
1
Review
24
Questions
24
Answers
Questions
Ask a question
1–10 of 24 Questions
Sort by:
▼
Menu
Flybird63
· 2 months ago
I'm using this with your 3 3/8 quad gauge and the up and down are backwards when calibrating it. Is this normal or do i have something hooked up wrong? I assume i have a stock 10-73 sender, but other sender options do the same thing.
1
answer
Answer this Question
Alex at AutoMeter · 2 months ago
Thank you for your question. I would recommend giving our tech support team a call so we can go through some troubleshooting and help figure out where the issue is. We are available Monday through Friday 8-5:00PM CST. 866.248.6357
Helpful?
Yes · 0
No · 0
Report
jim47
· 7 months ago
another question, does this unit work by giving a varying input voltage to the gauge or by varying the resistance on power coming from the gauge causing a drop in voltage across the circuit?
1
answer
Answer this Question
Jim from AutoMeter · 6 months ago
This works by PWM to ground, simulating a resistance.
Helpful?
Yes · 0
No · 0
Report
Filippone
· 6 months ago
Is it possible you could send me a new set of instructions on how to install the Audio Meter fuel bridge fuel link adapter. I purchased one of your fuel bridge adapters and lost the installation instructions for it and I need o reinstall it. Thank you
1
answer
Answer this Question
Paul G. · 6 months ago
Please give our technical support a call at 866-248-6357 for assistance on this.
Helpful?
Yes · 0
No · 0
Report
Btbur
· 7 months ago
Will 9109 help dampen the gauge needle from bouncing all over from fuel slushing around a non baffled tank?
1
answer
Answer this Question
Jim from AutoMeter · 7 months ago
The Fuel Bridge adapts out Air Core short sweep fuel level gauges to most senders. It does not have an anti-slosh damping function.
Helpful?
Yes · 0
No · 0
Report
jim47
· 7 months ago
my truck has only two poles on its gauge, one is power, the other is for the stock sending unit, the gauge normally works by using the sending unit as the ground, will this work in this setting?
1
answer
Answer this Question
Alex at AutoMeter · 7 months ago
Thank you for your question. The Fuel Bridge is only going to work with an Autometer short sweep electric gauge. It is not designed to work with any OEM gauges.
Helpful?
Yes · 0
No · 0
Report
Jamie1964
· 7 months ago
How to reset the fuel bridge unit? Need to use a differerent ohm setting. Absolutely nothing in the instruction about it!
1
answer
Answer this Question
Steve from AutoMeter · 7 months ago
There wouldn't be a reset for the fuel bridge as the preset can be changed on the unit whenever the end user makes changes to the setup. For further assistance, please contact us at 866-248-6357.
Helpful?
Yes · 0
No · 1
Report
Ryes
· 11 months ago
What is the output range on this, has alot of info on what it adapts from but what is the range it adapts to? IE if we have a 0-30Ohm sender, what is the gauge output from this device? What gauge range is required for this to be used?
1
answer
Answer this Question
Jim from AutoMeter · 11 months ago
This device allows you to use any Auto Meter 90 degree short sweep electric fuel level gauge with any stock or aftermarket fuel sending unit. So it doesn't matter if our gauge is 0-90, 73-10, 240-33 etc.
Helpful?
Yes · 0
No · 1
Report
jim47
· a year ago
Could you use this with a six volt gauge?
1
answer
Answer this Question
Alex at AutoMeter · a year ago
Thank you for your question. The fuel bridge is only designed to work on 12v systems with Autometer short sweep electric gauges. Unfortunately it will not work on a 6v system.
Helpful?
Yes · 0
No · 1
Report
City562
· a year ago
Will this work with the autometer 7006 invision? All other sending units have a reading, but not the fuel level.
1
answer
Answer this Question
Paul G. · a year ago
Unfortunately, no the fuel bridge will not work.
This kit is designed for multiple factory fuel senders. The resistance ranges that are compatible are: 0-90, 240-33, 73-10 (linear),
73-10 (non-linear), 16-158, 40-250, and 0-30 OHM. If you have a fuel sending unit other than those listed you will need to change the fuel
sender
Helpful?
Yes · 0
No · 1
Report
Shg3
· a year ago
Would this work with an autometer fuel sender unit in my fuel cell, but using my oem gauge which has a reading range of 10-130ohm.
1
answer
Answer this Question
Alex at AutoMeter · a year ago
Thank you for your question. Unfortunately the fuel bridge is only designed to work with Autometer short sweep electric gauges.
Helpful?
Yes · 0
No · 0
Report
1–10 of 24 Questions
Previous Questions
◄
Next Questions
►
Ask a question
You may also like: